Pin Router Plans

🔥+ Pin Router Plans 08 Aug 2020 Shop authentic G Plan Furniture furniture and other G Plan Furniture furniture ... Mid-Century Modern Danish Style Teak Chest of Drawers / Dresser by G Plan, ...

Pin Router Plans Barndominiums can be built in conjunction with a horse barn, shop, ... You'll be able to choose from several different floor plans as well as square foot plans in ...

Whirligig Kits Airplanes
the 1 last update 2020/08/08
Learn the best joinery techniques for a sag-free garden gate.
Author:
Patricia Poore
Updated:
Original:

Why Do Garden Gates Sag?

Garden gates sag because a square (or rectangular) frame is essentially unstable. Built with standard DIY woodworking joints, the gate will twist unless it is braced or pulled into tension. This tendency is exaggerated because a gate is held along only one side; the unhinged, free side sags from its own weight and from the trauma of being slammed. (And do you remember swinging on the backyard gate as a kid?)

Use quality materials and pro woodworking principles to design a garden gate that doesn’t sag. 

Douglas Keister

Best Practice

Pin Router Planshow to Pin Router Plans for Always use best-practice principles for fences and gates, or they won’t last five years. 

  • Use rot- and corrosion-resistant materials
  • Build to shed water
  • Avoid exposed end grain and water traps

Strength is important because a gate moves.

  • Sink posts into concrete 
  • Use heavy-duty fasteners
  • Make good, strong joints

As for wood choice, your best bet is a rot-resistant species (cedar, redwood, teak, mahogany). 

  • Cedar wins because teak is very expensive and has a high waste factor
  • Redwood should be used only if it is recycled old-growth lumber
  • Less-resistant mahogany needs a finish coating
  • Pressure-treated lesser woods are in disfavor because we now know that the preservatives do transfer (to the touch, and into the water table) and because cuts require highly toxic on-site treatment.

Two Strategies for Building a No-Sag Gate

The first two strategies for building a no-sag gate involve the principle of triangulation: introducing a diagonal to stabilize the square frame. 

Tension rod with turnbuckle. The tension solution uses a rod or a cable and turnbuckle, as shown, to keep the frame from twisting out of square.

Rob Leanna

  1. The Tension Solution: The tension solution uses a rod or a cable and turnbuckle, as shown, to keep the frame from twisting out of square. But “diagonal bracing is only as stable as the primary joint to which it’s fastened,” says woodworker Charles Prowell. “A turnbuckle cable requires periodic adjustment.”
  2. The Compression Solution: This solution makes use of a solid brace along the opposite diagonal.

Diagonal brace in compression. Diagonal bracing is only as stable as the primary joint.

Rob Leanna

Joinery

To ensure a tight mortise-and-tenon joint, drill the holes in the tenon just a bit off center from the holes you drill in the side of the post.

Rob Leanna

Rigid woodworking joints also will keep a gate from sagging. Rigidity keeps the frame from twisting. A pegged mortise-and-tenon joint is strong. You should try to cut the mortise accurately for a tight fit, but if there’s any play, shim around the tenon. Note that the pales (pickets) are inserted through holes drilled into the rails.

A dovetail joint is a great alternative.

Rob the 1 last update 2020/08/08 LeannaRob Leanna

Pin Router Planshow to Pin Router Plans for
To ensure a really tight mortise-and-tenon joint, drill the holes in the tenon just a bit off center from the holes you drill in the side of the post. This way, when you drive the pegs, they will act as a wedge, tightening the joint. This is called a draw-peg joint. Taper the ends of the pegs to help them go in easier. Cut the mortise a bit deep to allow for draw.

Pin Router Planshow to Pin Router Plans for A half-lap joint is easiest to cut.

Rob Leanna

A dovetail joint is your second alternative. Easiest to cut, but not as strong as the others, is the half-lap joint. Against crushable wood such as redwood, use a large, flat washer with the nut and bolt.

How to Construct the Gate Closure

Chain and weight closure.

Rob the 1 last update 2020/08/08 LeannaRob Leanna

Don’t use a screen-door spring closer! There’s just too much tension on one of these; slamming will cause the gate to wrack and vibrate apart in no time. The easiest solution is to forgo automatic gate closers entirely—simply close the gate manually behind you. Or install the hinged gatepost slightly out of plumb to encourage the gate to close itself.

An early solution (still used most picturesquely at Colonial Williamsburg) is a weight on a chain. No matter what the closing mechanism or the type of latch used, adding a stop piece the full height of the gate is very important. If the swinging gate is stopped against the post only at the latch point, it will wrack every time it closes.

Built to Last

Garden gates sag because a square (or rectangular) frame is essentially unstable.

Posts

Set gate posts in a concrete encasement typically three times the diameter of the post. Use post anchors where termites are common, or in very damp soils. A general rule of thumb is to sink a third of the total length of the post into the ground (two-thirds above grade). Cap post tops, or at least bevel-cut the tops to shed water.

Pin Router Planshow to Pin Router Plans for Fasteners

Best practice: brass screws, countersunk and plugged. At least use hot-dipped galvanized fasteners.

Finishes

Pin Router Planshow to Pin Router Plans for Whitewash and transparent stain can be touched up and don’t peel. Untreated cedar and redwood weather to a natural gray.

Hardware

Use latches and hinges meant for outdoor use, with unfussy mechanisms that will tolerate misalignment. Iron is traditional, but it stains when it rusts. Bronze hardware for outdoor use is now available. Brass hardware, available at marine suppliers, won’t rust, and you can paint it if you prefer.

Hardware Sources

Coastal Bronze
House of Antique Hardware
Sun Valley Bronze
Rocky Mountain Hardware
Van Dyke's Restorers

For gate resources, see our Products & Services Directory.

Art & Science of The Moon Gate

What''s specialty is creating insulating storm windows that the 1 last update 2020/08/08 disappear into your shaped openings - matching the shape exactly - from bent glass to odd shapes, sizes and thicknesses – disappearing into your window opening.What''s specialty is creating insulating storm windows that disappear into your shaped openings - matching the shape exactly - from bent glass to odd shapes, sizes and thicknesses – disappearing into your window opening.

Crown Point Cabinetry

Crown Point Cabinetry offers custom cabinets for period style kitchens, baths, offices, laundry rooms, home for 1 last update 2020/08/08 bars and more. Styles include Shaker, Arts & Crafts, Early American, Victorian and Transitional.Crown Point Cabinetry offers custom cabinets for period style kitchens, baths, offices, laundry rooms, home bars and more. Styles include Shaker, Arts & Crafts, Early American, Victorian and Transitional.